Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
Do you find yourself hunting for related information around Installing A Bathtub?
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily accessible, the job can relocate easily; if you have to open a wall to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the new one. Make sure you have qualified on your own for the work and also fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub up until the level reads level.
To set up taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the tub needs to wait till the bath tub has been made use of at the very least once as this will settle it into its final position.
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, causing complications with wetness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about How to Install a Bathtub, I assumed sharing that piece of writing was a good idea. If you please take the opportunity to distribute this article if you liked it. Thank you so much for going through it.
Contact Us Now Report this page